6xc
Moderators: deerhunter338mag, stokesrj, trazman
- Corjack
- Administrator
- Posts: 10260
- Joined: Thu Jun 11, 2009 2:28 pm
- Location: Missouri
- Location: Booger county Missouri
- Contact:
6xc
Had a Blaser 6xc barrel for a few years now . Decided to try a 6mm for PRS this year. I have been collecting parts for the last three months .
Blue printed 700 body.
PTG fluted bolt small firing pin.
Badger bolt knob.
26 inch Criterian varmint contour 6xc barrel 7.5 twist.
APA little batturd brake.
KRG Bravo stock.
1# Triggertech Trigger. (Not in yet)
I have a Manners PRS 1 on order due in the end of March. I grabbed one of the new KRG Bravo stocks with the same backbone as my Whisky 3 chassis. 400.00 retail. I really like it. For a cheap stock I see no reason a fellow could not compete with it. When the Manners gets in, I will swap it out to a Creedmoor that I am also working on.
I got home from Dallas Safari Club show, with a bad cold. Layed around last couple days. Ran over to a buddy's, and used his hydraulic press and action wrench to install and headspace the barrel yesterday. Got home and mounted a scope, and kinda got it on paper at 100 yards. Shot about a dozen rounds through it, but could not help but notice it was shooting well. These were odd and ends of ammo loaded for the R8 Blaser.
Today I shot 9 rounds out of it before I got rained out today. 105 Berger Hybrids.
RL16,
37.3 grains
37.6 grains 2989 fps 13 es.
37.9 grains
The neck bushing I have is .268. It is not giving me much neck tension. Think I need a 267. The first load went a bit under .5, the second went into one hole, the third, went well under a half. Pictures are of the second and third groups. Got about 20 more Berger in this box, and then I will switch to 110 SMKs and 115 DTAKs.
Looks like it will be very cooperative. Kicks like a 22 magnum.
Blue printed 700 body.
PTG fluted bolt small firing pin.
Badger bolt knob.
26 inch Criterian varmint contour 6xc barrel 7.5 twist.
APA little batturd brake.
KRG Bravo stock.
1# Triggertech Trigger. (Not in yet)
I have a Manners PRS 1 on order due in the end of March. I grabbed one of the new KRG Bravo stocks with the same backbone as my Whisky 3 chassis. 400.00 retail. I really like it. For a cheap stock I see no reason a fellow could not compete with it. When the Manners gets in, I will swap it out to a Creedmoor that I am also working on.
I got home from Dallas Safari Club show, with a bad cold. Layed around last couple days. Ran over to a buddy's, and used his hydraulic press and action wrench to install and headspace the barrel yesterday. Got home and mounted a scope, and kinda got it on paper at 100 yards. Shot about a dozen rounds through it, but could not help but notice it was shooting well. These were odd and ends of ammo loaded for the R8 Blaser.
Today I shot 9 rounds out of it before I got rained out today. 105 Berger Hybrids.
RL16,
37.3 grains
37.6 grains 2989 fps 13 es.
37.9 grains
The neck bushing I have is .268. It is not giving me much neck tension. Think I need a 267. The first load went a bit under .5, the second went into one hole, the third, went well under a half. Pictures are of the second and third groups. Got about 20 more Berger in this box, and then I will switch to 110 SMKs and 115 DTAKs.
Looks like it will be very cooperative. Kicks like a 22 magnum.
You do not have the required permissions to view the files attached to this post.
-
- Global Moderator
- Posts: 1840
- Joined: Wed Jul 13, 2011 12:56 pm
- Location: Texas
- Location: Texas
Re: 6xc
I'd be happy with that group!
It doesn't matter what you shoot as long as you shoot
NRA Benefactor Member
SCI Life Member
USMC Life Member
NRA Benefactor Member
SCI Life Member
USMC Life Member
-
- Meister der jagd
- Posts: 1154
- Joined: Mon Jul 14, 2014 10:42 pm
- Location: USA
- Location: Bakersfield, CA
Re: 6xc
It's looking good so far. What do you think is causing light neck tension, are your necks thinning or are your bullets a little undersized?
I have never met a man so ignorant that I couldn't learn something from him. Galileo
The fact that Jellyfish have survived 650 million years, despite not having brains, gives hope to many people. sun-gazing.com
The fact that Jellyfish have survived 650 million years, despite not having brains, gives hope to many people. sun-gazing.com
- Corjack
- Administrator
- Posts: 10260
- Joined: Thu Jun 11, 2009 2:28 pm
- Location: Missouri
- Location: Booger county Missouri
- Contact:
Re: 6xc
dchamp wrote:It's looking good so far. What do you think is causing light neck tension, are your necks thinning or are your bullets a little undersized?
Too big if a bushing.
- stokesrj
- Moderator
- Posts: 5921
- Joined: Mon Jun 17, 2013 12:41 pm
- Location: USA
- Location: Mesa AZ, USA
Re: 6xc
Or, too thin of a neck wall thickness I'm running a .267 bushing with a neck wall thickness of .0127", Lapua brass. .267-(.0127X2)=.2416 which is a neck tension of .2416-.243=.0014". I find this just about right in my 6mm Norma BR. Neck tension will change over time as the brass work hardens and loses it's springiness. So I would hold on to that .268 bushing, you might need it in the future. I always, or at least should always, buy bushings in sets of three, what I calculate I need and one up and one down by .001".Corjack wrote:dchamp wrote:It's looking good so far. What do you think is causing light neck tension, are your necks thinning or are your bullets a little undersized?
Too big if a bushing.
Robert J Stokes
-
- Posts: 447
- Joined: Mon May 05, 2014 5:38 pm
- Location: Eugene OR USA
Re: 6xc
Corjack:
Impressive. You may have a weapon system that could meet the All Day BlaserBuds 0.5MOA Challlenge. Show those dudes running 6mm Creeds.
Why the Triggertech trigger? To try or you have reasons to believe it is superior to the well established brands? On their website it is stated they guarantee the trigger during its lifetime.
"Our triggers come with a satisfaction guarantee and warranty for the product’s lifetime enabling you to buy with confidence."
I interpret that to mean their trigger, and in fact all triggers, do have a finite lifetime under harsh conditions such as in the PRS. Barrels have a finite lifetime. Does every component of a rifle, i.e. barrel,trigger, action, bottom metal and stock, have a finite lifetime determined by desired weapon system accuracy?
Impressive. You may have a weapon system that could meet the All Day BlaserBuds 0.5MOA Challlenge. Show those dudes running 6mm Creeds.
Why the Triggertech trigger? To try or you have reasons to believe it is superior to the well established brands? On their website it is stated they guarantee the trigger during its lifetime.
"Our triggers come with a satisfaction guarantee and warranty for the product’s lifetime enabling you to buy with confidence."
I interpret that to mean their trigger, and in fact all triggers, do have a finite lifetime under harsh conditions such as in the PRS. Barrels have a finite lifetime. Does every component of a rifle, i.e. barrel,trigger, action, bottom metal and stock, have a finite lifetime determined by desired weapon system accuracy?
Paper is my game, steel the same.
- Joe338ST
- Meister der jagd
- Posts: 1816
- Joined: Sat Oct 21, 2017 8:32 am
- Location: Australia
Re: 6xc
Just wait for your triggertech trigger. Chalk and cheese the premium triggers compared to factory. Just love the Jewel trigger on my Remington 700!
Joe
Joe
Joe
I hunt, I shoot, I camp, I fish. They are the great reset buttons in my life.
I hunt, I shoot, I camp, I fish. They are the great reset buttons in my life.
- Corjack
- Administrator
- Posts: 10260
- Joined: Thu Jun 11, 2009 2:28 pm
- Location: Missouri
- Location: Booger county Missouri
- Contact:
Re: 6xc
Slowly but surely the 6xc project is coming along. Not sure the Sierra 110s will stabilize at low elevations, and longer ranges . Had a sample of uncharted 115 DTAC bullets. They are shooting pretty good. This morning shot 6 and had an average of 2947 fps ES of 13, and an SD of 4. Got a box of 500 in today that are boron coated. David Tubb says these will just about shoot themselves. Go up to a stage, throw the rifle down, then stand back. Easy peasy! Dave says you can go longer between cleanings with the coated bullets. Since I hardly ever clean a barrel, that suits me fine.
You do not have the required permissions to view the files attached to this post.